NetBIOS name

/usr/bin/defaults read /Library/Preferences/SystemConfiguration/com.apple.smb.server NetBIOSName will tell you what the name is.

sudo /usr/bin/defaults write /Library/Preferences/SystemConfiguration/com.apple.smb.server NetBIOSName NAMEYOUWANT will set it.

Not sure if you're familiar with scutil to set the HostName/LocalHostName/ComputerName...

/usr/sbin/scutil --get LocalHostName
sudo /usr/sbin/scutil --set LocalHostName NameYouWant

Then you could use:
sudo /usr/bin/defaults write /Library/Preferences/SystemConfiguration/com.apple.smb.server.plist NetBIOSName $(/usr/sbin/scutil --get LocalHostName)

Thanks I'll try it out

A little clarification - there are three "names" applied to Macintosh OSX computers.

Using the command "scutil", they are defined as: HostName = the Unix name for the device (under Server, this should be a fully qualified domain name) ComputerName = the Mac OS name for the device (the name broadcast on the network) LocalHostName = the "zeroconf" network name for the device (a.k.a. - Apple's "Bonjour" protocol)

The JSS uses the ComputerName for most of its operations. This is also the source of the Active Directory NetBIOSName (usually reduced to all lower case during binding). Should be limited to 15 standard ASCII characters if joining Active Directory.

If you use the "scutil" command to rename the device, you should sett ALL three names to the same value.

The Mac OS tends to link the LocalHostName to the ComputerName if you change the ComputerName in System Preferences:Sharing.

I can the commands and it did change the NetBios name but after rebooting it reverted back to what it was before I changed it.
I used:

/usr/bin/defaults read /Library/Preferences/SystemConfiguration/com.apple.smb.server

sudo /usr/bin/defaults write /Library/Preferences/SystemConfiguration/com.apple.smb.server NetBIOSName NAMEYOUWANT
and then I even tried:

sudo /usr/bin/defaults write /Library/Preferences/SystemConfiguration/com.apple.smb.server.plist NetBIOSName $(/usr/sbin/scutil --get LocalHostName)

And both had the same results, They appeared to work but the after reboot they changed back.

@ciretruk

If you have an "Update Inventory" policy make sure your Maintenance payload doesn't have the "Reset Computer Names" checked. This can cause your computer names to get reverted back at specific times depending on the frequency you run the policy.

Just something to check

Chuck

Thanks Chuck,
I checked and no "reset computer names" was not checked.

Perhaps you should try this:

1. Unbind from Active Directory

2. Run the following terminal commands on the target computer: sudo /usr/sbin/scutil --set HostName NameYouWant sudo /usr/sbin/scutil --set LocalHostName NameYouWant sudo /usr/sbin/scutil --set ComputerName NameYouWant

3. Restart the computer and verify the name has been retained using the "scutil --get" command.

4. Recon the computer using Casper Suite:Recon; or "sudo jamf recon"

5. Re-bind the computer to Active Directory.

The NetBios name will revert to whatever it is getting from a PTR record even if the LocalHostName is changed using scutil. This is probably a bug, but unfortunately that means DDNS used by Windows machines can mess up NETBIOS advertisements on Mac. Particularly if a VPN connection is involved since macOS doesn't seem to register the IP address over DCE/RPC properly so you can't fix this by binding to the domain. You basically end up with the Mac advertising a stale DDNS record for another machine. I haven't found a way around this.

Thanks eclemens, That worked out perfectly for me

This is what I observed as well. We used a fairly agressive policy to update netbios names from all configurations files and they keep resetting. Even if we update them on the computers manually.

Did you figure out a different solution ?

Thanks

Oddly having NetBIOSName issues even though our network guys tell us that NetBIOS isn't an issue, yet security is asking us about weird named computers that we don't have listed having. THIS ^^^ worked!!! Thank you Robert!